search

Scosche EFX Mono Amplifier Manuel d'installation

Naviguer en ligne ou télécharger Manuel d'installation pour Récepteurs AV Scosche EFX Mono Amplifier. Scosche EFX Mono Amplifier Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 8
  • Table des matières
  • MARQUE LIVRES
    • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
EFX AUDIO IS A DIVISION OF SCOSCHE INDUSTRIES, INC. ©2009 500c1/1000c1 02.09
500c1/1000c1
1-CHANNEL (MONO) AMPLIFIERS
INSTALLATION MANUAL
EFX AMPLIFIER FEATURES
500c1 SPECIFICATIONS
BEFORE YOU BEGIN:
Read all instructions and Cautions.
Disconnect Negative terminal of Vehicle battery.
Digital Multi-Meter
EFX Amplifier Wiring Kit, EFX REVOPAK4 is
recommended for these amplifiers.
Wire Strippers and Cutters
Drill and Drill Bits
Electrical Tape
Tools & Supplies
Installation procedures:
Plan your installation completely before beginning.
Be sure you have all materials needed to complete your installation.
Please call us with any questions before you start at:
Location/Mounting Amplifier
500c1
- 18dB Adjustable Full/Low Pass
- Electronic Crossover (40Hz~400Hz)
- 2-Ohm Load Capability
1000c1
- 18dB Adjustable Low Pass
- Electronic Crossover (40Hz~200Hz)
- 1-Ohm Load Capability
- Strapable
Power Output: 350 Watts RMS x 1 Channel at 4 Ohms and 1% THD+N
Signal to Noise Ratio: >80 dBA (reference:1 Watt into 4 Ohms)
Additional Power Output: 500 Watts RMS x 1 Channels at 2 Ohms at 1% THD+N
Frequency Response: 20Hz -20kHz (-3dB)
Maximum Input Signal: 6V (Low Level) / 10V (High Level
Minimum Input Signal: 200mV (Low Level) / 420mV (High Level)
1000c1 SPECIFICATIONS
Power Output: 350 Watts RMS x 1 Channel at 4 Ohms and 1% THD+N
Signal to Noise Ratio: >80 dBA (reference:1 Watt into 4 Ohms)
Additional Power Output: 500 Watts RMS x 1 Channels at 2 Ohms at 1% THD+N
1000 Watts RMS x 1 Channels at 1 Ohms at 1% THD+N
Frequency Response: 20Hz -200Hz (-3dB)
Maximum Input Signal: 6V (Low Level) / 10V (High Level)
Minimum Input Signal: 200mV (Low Level) / 420mV (High Level)
- 0-12dB Variable 45Hz Bass Boost
- RCA Line Level Output Loop-Thru
- Line Level & Speaker Level Inputs
- Soft Start Turn-on/off
- 5-Way Protection (Thermal, Short Circuit,
Impedance, Voltage, Reverse Polarity)
- MOSFET Power Switching Transistors
- Brushed Aluminum Heatsink and Top Plate
- Sturdy Aluminum Side Panels
- Illuminated Logo Badge
IMPORTANT/ PRELIMINARY
Select a safe/dry location to mount your Amplifier. Double check location and placement of
your amplifier before making any connections or drilling any holes. Never mount your Amplifier
in the engine compartment, or cover it with carpet or any other fabric materials that will cause
the Amplifier not to get the proper ventilation. Avoid drilling through electrical wires, fuel lines,
or other obstructions that may be around your mounting area. If you have any questions or
concerns, please contact our tech support team at 1-800-621-3695 Ext. 3
Vue de la page 0
1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - 500c1/1000c1

EFX AUDIO IS A DIVISION OF SCOSCHE INDUSTRIES, INC. ©2009 500c1/1000c1 02.09500c1/1000c11-CHANNEL

Page 2 - LED STATUS INDICATOR

IMPORTANT/ PRELIMINARYROUTING CABLES AND WIRESDetermine the safest place to run wires through firewall. If it is necessary to drill holes be surearea

Page 3 - AMPLIFIER ADJUSTMENTS

AMPLIFIER ADJUSTMENTSLevel:The Level Adjust Control (Gain) matches the output of your Car Stereo to theinputs on the Amplifier.1. Turn Stereo on and a

Page 4 - AMPLIFIER WIRE GAUGE KIT

4-CHANNEL HIGHPOWERPOWERING YOUR AMPLIFIERFuses: Use only specified fuses (see note).NOTE: Use three 25A ATC fuses for 500c1, or use four 25A ATC fuse

Page 5 - SPEAKER OUTPUTS

SPEAKER OUTPUTSSpeaker connections are used to connect the speakers to the amplifier. Be sure speakers with the appropriate *impedances are used. It i

Page 6 - HI INPUT

MASTER/SLAVE CONFIGURATION1000W MONO HIGH POWER CLASS-D AMPLIFIERONPROTGNDPOWERBREMPHASEHI INPUTGNDL RREMOTEMASTER/SLAVESLAVE MASTERLEVELMAXMINBASS12d

Page 7 - MORE TIPS ON PAGE 8

TROUBLE SHOOTINGUse a volt meter to verify voltages atterminals of amplifiers +12V Inputshould have a minimum of 11.5 voltswhile ignition of vehicle i

Page 8

TROUBLE SHOOTINGCheck amplifier’s input gain controlsettings - adjust levels if necessary.Verify battery voltage is greater than 11.5v DC at amplifier

Commentaires sur ces manuels

Pas de commentaire
  • Astrotek Chanson Water Kissla Lance Industries Oxford-garden
  • Dynex TV LCD Fisher-Price Détecteurs radar JVC Surveille le CRT Parasound Amplificateurs audio National Instruments Modules émetteurs-récepteurs de réseau
  • Clarion VMA5092 Canon i-SENSYS LBP312x Nokia N82 Acer AT2225 Samsung SM-T715
  • Massive 37370/43/10 Manuel Vertex Standard VX-4000 Manuel de l'utilisateur AEG HK854401FB Manuel de l'utilisateur Honeywell PCR426W Manuel de l'utilisateur ENHANCED VISION pebble-mini Manuel de l'utilisateur